VapeWholesaleHub  |  Wholesale supplier · Shenzhen, China
Tel / WeChat / WhatsApp: +86 13711127975  |  vape@0099933.xyz
Home  /  Starter Vape Kit  /  Choosing Starter Vape Kit base brief
starter vape kits · importers

Choosing Starter Vape Kit base brief

This page is for importers who want a working answer on specification, price and lead time before they commit a purchase order. We have written the detail down so nobody has to sit through a sales call to extract it.

Published 26 May 2026  ·  VapeWholesaleHub  ·  Reading time 7 min

Close inspection of the assembly line before the batch is released.
Close inspection of the assembly line before the batch is released.
Bulk packing station during the run for a importers order.
Bulk packing station during the run for a importers order.
Carton-ready units from the same batch, coded for traceability.
Carton-ready units from the same batch, coded for traceability.

The reorder is the real test

If you are comparing three quotes for starter vape kit, compare the paperwork first. Test reports, artwork files, batch coding and the replacement clause tell you more about a supplier than the unit price on page one.

For private label accounts we hold the artwork files and the approval record. Rebranding a line eighteen months later is then a file update instead of a redesign.

Every account gets a named contact who has actually seen the product. Being passed between three people to answer one question about a coil resistance is the fastest way to lose a buyer, so we do not organise support that way.

How the price is actually built

Custom printing raises the unit price and lowers the marketing cost. For importers the break-even is usually reached on the second or third repeat order, not the first, so we quote both branded and neutral options.

The cheapest way to lower your cost per unit is usually to remove a SKU, not to negotiate a discount. Fewer lines means larger runs, fewer changeovers and a better price at the same quality.

For importers, the practical answer is usually a shorter range: two core lines, one step-up, one trial SKU. Everything else is inventory risk wearing a nice finish.

How we structure a first order

The first question we ask is not what you want to spend. It is what your customer already buys. Answer that and the starter vape kit list writes itself; skip it and you end up with a pallet of stock that photographs well and sells badly.

We keep a short list of approved configurations for starter vape kits. Anything outside that list is possible, but it becomes a custom run with a custom lead time, and we quote it as such rather than pretending everything is standard.

  • Seven-day defect reporting with replace-or-credit
  • Document pack prepared per destination market
  • Private label files archived for future rebrands
  • Consolidated or split shipping, quoted both ways
  • Reference sample retained from every batch
  • Mixed SKU cartons to spread first-order risk

Where defects actually come from

Battery safety is not a marketing line. Cells are matched by capacity and internal resistance before assembly, charging boards are checked for cut-off voltage, and any unit that fails the cut-off test never reaches packing.

Leak complaints almost always trace back to one of three things: an over-torqued centre post, a seal that sat in a hot container, or a fill volume pushed past the design limit. We cap fill volume slightly below maximum for exactly that reason.

Specification summary

Typical specification for this category
Battery800 mAh
Pod capacity2.0 ml
Coil resistance1.0 ohm
IncludedDevice, pod, cable
ChargingUSB-C 5V/1A
PackagingBlister pack
Minimum order300 units per SKU, mixed cartons allowed
Lead time30 working days after artwork approval

If any of this is unclear, the fastest route is a message rather than a meeting. Send the market you sell into and the price band you work in, and you will get a specific answer instead of a brochure.

Frequently asked

What happens if part of the order is defective?

Report within seven days with photos and the batch code. Confirmed defects are replaced or credited on the next shipment. The failure is logged by mode and batch, and reviewed monthly with the factory.

What is the minimum order for starter vape kit?

Standard configurations start at 240 units per SKU, with mixed SKUs allowed inside the same carton. Custom colours, custom packaging or a private label run usually start at 600 units because of setup time on the line.

Do you support private label?

We do. Send your artwork or your brand direction and we will return a digital proof, then a physical dummy for colour approval. Packaging files stay on record so a rebrand later is a file update rather than a redesign.

Related reading

Need a quotation on starter vape kits?

Send destination market, target price and quantity. Same-day reply on working days.

Tel / WeChat / WhatsApp +86 13711127975  ·  vape@0099933.xyz

Talk to the supply team

Ask for a quotation on starter vape kits

Tell us the market you sell into and the price band you work in. You will get a specification and a landed cost estimate, not a catalogue dump.

What to send

Destination market, target retail price, quantity per SKU, and whether you need private label. With those four lines we can quote the same day.

Samples ship by air express and the cost is credited against your first production order.

Email the team
WhatsApp Email us