VapeWholesaleHub  |  Wholesale supplier · Shenzhen, China
Tel / WeChat / WhatsApp: +86 13711127975  |  vape@0099933.xyz
Home  /  Starter Vape Kit  /  Starter Vape Kit finish before you order guide
starter vape kits · importers

Starter Vape Kit finish before you order guide

We work with importers who order between a few hundred and a few thousand units at a time, and we treat both ends the same way: a written specification, a sample you approve, and a production run that matches the sample.

Published 23 November 2024  ·  VapeWholesaleHub  ·  Reading time 9 min

Packaging proof for the export market, approved before the run.
Packaging proof for the export market, approved before the run.
Starter Vape Kit finish before you order guide configuration from a production run, photographed before packing.
Starter Vape Kit finish before you order guide configuration from a production run, photographed before packing.
Unit from the retained reference sample held against this order number.
Unit from the retained reference sample held against this order number.

What a sensible opening order looks like

Starter Vape Kit sits in a crowded price band, and the cheapest quote on the sheet is rarely the cheapest unit on your shelf. Everything below is built around reorder rate, defect rate and cash conversion rather than headline unit price.

Colour range is where assortments quietly die. Six finishes look impressive in a brochure and disastrous on a shelf with 40 cm of space. We recommend two finishes per core SKU and let the trial line carry the novelty.

A practical starting order for importers is 240 units across two or three SKUs, not 240 units of one. That spreads the risk, gives your staff something to compare, and still hits the first price break.

Shipping without surprises

Damage in transit is nearly always a packing decision, not bad luck. Double-walled cartons, internal dividers and a drop-tested configuration cost a little more and save the argument at the other end.

We ship from Shenzhen and Guangzhou: air express for samples and part loads, sea freight for volume. Typical production lead time is 22 working days after artwork approval, plus transit. We quote both routes so you can see the trade-off instead of guessing at it.

For importers, the practical answer is usually a shorter range: two core lines, one step-up, one trial SKU. Everything else is inventory risk wearing a nice finish.

Turning shelf space into repeat visits

Staff knowledge converts better than any poster. If your team can explain the difference between two coils in one sentence, the step-up SKU sells itself.

Counter space is finite. Three well-chosen SKUs outsell nine crowded ones, and the empty space signals a curated range rather than a clearance table.

  • Artwork proof plus physical dummy for custom packaging
  • Cartons drop-tested and pallet-counted for clean freight
  • Reference sample retained from every batch
  • Mixed SKU cartons to spread first-order risk
  • Batch codes traceable from carton back to production date
  • Private label files archived for future rebrands

Batch consistency and why it matters

We photograph the packing station during production for volume orders. It is a small thing, but it settles most arguments about what was actually in the carton before it was sealed.

Cosmetic grading is written down, not argued about. Minor scuffs inside the tolerance band are accepted; anything that would make a customer put the unit back on the shelf is rejected. Your staff should never have to explain a finish defect to a paying customer.

Specification summary

Typical specification for this category
Battery800 mAh
Pod capacity3.0 ml
Coil resistance0.8 ohm
IncludedDevice, pod, cable
ChargingUSB-C 5V/1A
PackagingRetail box
Minimum order100 units per SKU, mixed cartons allowed
Lead time25 working days after artwork approval

If any of this is unclear, the fastest route is a message rather than a meeting. Send the market you sell into and the price band you work in, and you will get a specific answer instead of a brochure.

Frequently asked

Can we order samples before committing?

Yes. Sample orders are shipped by air express and the cost is credited against your first production order above 240 units. We would rather you handle the sample than approve a specification from a photograph.

What is the minimum order for starter vape kit?

Standard configurations start at 240 units per SKU, with mixed SKUs allowed inside the same carton. Custom colours, custom packaging or a private label run usually start at 600 units because of setup time on the line.

How long does production take?

Around 22 working days after artwork approval for stock configurations, plus transit. Custom runs add roughly a week for tooling and a physical dummy. We confirm the date in writing on the order acknowledgement.

Related reading

Need a quotation on starter vape kits?

Send destination market, target price and quantity. Same-day reply on working days.

Tel / WeChat / WhatsApp +86 13711127975  ·  vape@0099933.xyz

Talk to the supply team

Ask for a quotation on starter vape kits

Tell us the market you sell into and the price band you work in. You will get a specification and a landed cost estimate, not a catalogue dump.

What to send

Destination market, target retail price, quantity per SKU, and whether you need private label. With those four lines we can quote the same day.

Samples ship by air express and the cost is credited against your first production order.

Email the team
WhatsApp Email us