VapeWholesaleHub  |  Wholesale supplier · Shenzhen, China
Tel / WeChat / WhatsApp: +86 13711127975  |  vape@0099933.xyz
Home  /  Starter Vape Kit  /  Starter Vape Kit private label artwork — a overview
starter vape kits · importers

Starter Vape Kit private label artwork — a overview

There is no shortage of suppliers quoting starter vape kit. The scarce thing is a supplier who will tell you which SKU to drop. We have been shipping starter vape kits long enough to know that the honest answer is usually a shorter list, and that is the answer we give.

Published 23 May 2026  ·  VapeWholesaleHub  ·  Reading time 9 min

Bulk packing station during the run for a importers order.
Bulk packing station during the run for a importers order.
Surface finish under raking light, one of the cosmetic checks.
Surface finish under raking light, one of the cosmetic checks.
Unit from the retained reference sample held against this order number.
Unit from the retained reference sample held against this order number.

After-sales, replacements and reorders

Buyers come to us for starter vape kit after a bad quarter: dead stock on one side, empty shelves on the other. The cause is usually the same, an assortment built from a catalogue instead of from sell-through data. This page explains how we rebuild that balance for importers.

Technical questions usually arrive at the worst possible moment, which is why we answer them on WhatsApp as well as email. A photo and a two line message resolves most issues faster than a ticket.

Returns are handled as data, not as complaints. Every reported failure is logged by mode and by batch, and the pattern is reviewed monthly with the factory.

How orders move from factory to shelf

We ship from Shenzhen and Guangzhou: air express for samples and part loads, sea freight for volume. Typical production lead time is 12 working days after artwork approval, plus transit. We quote both routes so you can see the trade-off instead of guessing at it.

Damage in transit is nearly always a packing decision, not bad luck. Double-walled cartons, internal dividers and a drop-tested configuration cost a little more and save the argument at the other end.

For importers, the practical answer is usually a shorter range: two core lines, one step-up, one trial SKU. Everything else is inventory risk wearing a nice finish.

Batch consistency and why it matters

Leak complaints almost always trace back to one of three things: an over-torqued centre post, a seal that sat in a hot container, or a fill volume pushed past the design limit. We cap fill volume slightly below maximum for exactly that reason.

A 0.5 percent defect rate sounds excellent until it lands on a 600 unit order and you are handling three returns in a week. We quote realistic rates per category and we credit in advance for the known failure modes.

  • Specification locked in writing before production starts
  • Document pack prepared per destination market
  • Consolidated or split shipping, quoted both ways
  • Standing reorder schedule with a fixed cut-off
  • Artwork proof plus physical dummy for custom packaging
  • Seven-day defect reporting with replace-or-credit

Assortment planning without the guesswork

A practical starting order for importers is 200 units across two or three SKUs, not 200 units of one. That spreads the risk, gives your staff something to compare, and still hits the first price break.

Colour range is where assortments quietly die. Six finishes look impressive in a brochure and disastrous on a shelf with 40 cm of space. We recommend two finishes per core SKU and let the trial line carry the novelty.

Specification summary

Typical specification for this category
Battery500 mAh
Pod capacity2.0 ml
Coil resistance1.2 ohm
IncludedDevice, 2 pods, cable
ChargingUSB-C 5V/1A
PackagingBlister pack
Minimum order200 units per SKU, mixed cartons allowed
Lead time25 working days after artwork approval

If any of this is unclear, the fastest route is a message rather than a meeting. Send the market you sell into and the price band you work in, and you will get a specific answer instead of a brochure.

Frequently asked

How long does production take?

Around 12 working days after artwork approval for stock configurations, plus transit. Custom runs add roughly a week for tooling and a physical dummy. We confirm the date in writing on the order acknowledgement.

What is the minimum order for starter vape kit?

Standard configurations start at 200 units per SKU, with mixed SKUs allowed inside the same carton. Custom colours, custom packaging or a private label run usually start at 500 units because of setup time on the line.

How do you handle repeat orders?

The specification is held on file against your account, so a reorder is a reference rather than a new brief. We recommend a standing schedule with a fixed weekly cut-off so stock lands before the shelf empties.

Related reading

Need a quotation on starter vape kits?

Send destination market, target price and quantity. Same-day reply on working days.

Tel / WeChat / WhatsApp +86 13711127975  ·  vape@0099933.xyz

Talk to the supply team

Ask for a quotation on starter vape kits

Tell us the market you sell into and the price band you work in. You will get a specification and a landed cost estimate, not a catalogue dump.

What to send

Destination market, target retail price, quantity per SKU, and whether you need private label. With those four lines we can quote the same day.

Samples ship by air express and the cost is credited against your first production order.

Email the team
WhatsApp Email us